Avid Technology AirSpeed 5000 Guide d'installation Page 69
- Page / 138
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Connecting the Power Cords
55
Connecting the Power Cords
The last step you must perform when cabling up your AirSpeed 5000 is to connect the power
cords. Two U.S. IEC power cords are shipped with the unit. If your local power distribution is
not compatible with the supplied cords, you must provide your own IEC power cables that are
compatible with your country’s power system. The power connector accepts 100 to 240 Vac,
50/60 Hz.
To connect power:
1. Attach the power cords to both power receptacles on the rear of the AirSpeed 5000.
2. Connect the other end of both power cords to a properly grounded stable power source.
The system will power on after you connect the first power supply. The Monitor application
will also automatically launch.
Once powered on, you must set up your system. For more information, see “Turning On the
Avid AirSpeed 5000 Server” on page 56.
c
For maximum power protection, Avid recommends a surge protected un-interruptible
power supply (UPS).
Power Supply 2
LAN1
LAN2
LAN3
LAN4
Power Supply 1
- AirSpeed 1
- Setup Guide 1
- Legal Notices 2
- Trademarks 4
- Contents 6
- Using This Guide 12
- Symbols and Conventions 13
- If You Need Help 14
- Avid Training Services 14
- Unpack and Inspect Checklist 15
- Unpacking Your System 16
- Verifying Components 17
- Server Components 19
- AIRSPEED 5000 20
- Data Drives 21
- Data Drive LED Functions 21
- System Control Panel 22
- Empty Empty Empty Empty 24
- System drives 26
- Power Supply 2 26
- Power Supply 1 26
- USB ports (2) 27
- MULTI I/O 29
- (2-Channel Models Only) 31
- MPEG-2 HD Codec Module Kit 32
- AVC-Intra Codec Module Kit 32
- Two (2) Thumbscrews 35
- Card Guide thumbscrew 35
- SATA Cables (red) 36
- Board Locking Bracket 37
- Thumbscrews 37
- Standos for codec 38
- Hold Down Bracket 41
- LSI Cable 41
- Hold Down Bracket slots 41
- Rack-mount Requirements 43
- Separating the Slide Rails 45
- Round hole adapter 48
- Bracket assembly tabs 48
- Front Panel Screws 51
- Fault LED (red) 53
- Power/Activity LED (blue) 53
- Drive lock 53
- Drive carrier latch 53
- Do one of the following: 57
- Video OUT 1 Video OUT 2 60
- Video OUT 4 60
- Video OUT 3 60
- Multi I/O 60
- Expansion Card 60
- Monitor OUT 1 61
- Monitor OUT 2 61
- Monitor OUT 4 61
- Monitor OUT 3 61
- Connecting Video Reference 62
- Connecting LTC 63
- Connecting Ethernet 64
- Intel Pro 1000 1Gb 65
- Ethernet ports 65
- Intel 82574L Gigabit 65
- Network Connection 65
- Connecting Serial 66
- Connecting a GPIO Device 67
- Connecting the Power Cords 69
- Performing System Diagnostics 71
- Diagnostic Window Explained 72
- Starting the Hardware Test 75
- Playing a Video Frame 76
- To capture video: 77
- Testing Audio Outputs 78
- Testing Disk Performance 80
- Error Log 81
- Diagnostic Test Failed 81
- Specifying a Computer Name 84
- Assigning an IP Address 85
- Device Service 90
- AirSpeed 5000 93
- Re-imaging Your System 95
- 25. Click Remove 99
- Preventative Maintenance 100
- Monitor Application 105
- Accessing the Knowledge Base 106
- A Specifications and Notices 107
- Dimensions and Weight 108
- Environmental Specifications 108
- Acoustic Specifications 109
- Power Specifications 109
- Video Channels 110
- Parameter Specification 111
- AVC-Intra) 112
- Audio Specifications 113
- Conversion 114
- Redundancy 115
- File Ingest/Exchange 115
- Connection Specifications 116
- Command Description 119
- Reference 122
- Connecting Monitor Out 124
- BNC Adapter - Attaches to 124
- 1 LTC Single ended input 125
- Warnings and Cautions 127
- FCC Notice 128
- LED Safety Notices 129
- (Hebrew LED Safety Notices) 130
- European Union 132
- Japan EMC Regulations 132
- Korean EMC Regulations 133
- Taiwan EMC Regulations 133
- 10. Replaceable batteries 136
- Technical Support (USA) 138
- Product Information 138
Produits connexes et manuels pour Serveurs Avid Technology AirSpeed 5000
Serveurs Avid Technology AS3000 Spécifications
(134 pages)
(134 pages)
SINGER Máquinas De Coser manuales de usuario
Empezando en F
| Modelos | Tipo de documento |
|---|---|
| Fashion Mate 7256 | |
| FEATHERWEIGHT FW-75 | |
| FUTURA CE-150 | |
| FUTURA CE-250 | |
| Futura SES2000 | |
| FUTURA XL-400 | |
| FW75 |
© 2020, manymanuals.fr. Tous droits réservés | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels