Avid Technology System 5 Guide de l'utilisateur Page 180
- Page / 190
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
System 5 Digital Audio Mixing System User Guide172
Dual Joystick Panel
The Dual Joystick Panel houses two joysticks in a full-width panel mounted in the CM403 module.
Assigning a Channel to a Joystick
Assign a channel to the joystick with the same key strokes used to assign a channel to a strip (see page 69).
Joystick Assign Mode
The Joystick Assign Mode is in Strip Config Panel Page 3 (see below).
Joystick Panel controls (only one joystick shown)
Joystick Assign Mode
100%
C1
Pan
L/R
Snd
F/B
Link
Solo
Pan Engage
Surround Engage
Link Key
Turns joystick
motor on and off
Joystick
Select/Punch key
Wave key is used with
Select/Punch key to set
automation mode, link to
a strip, or lock from layouts
Joystick position matrix
is 19 x 19 LEDs. A
single green LED
indicates the current
position and a diamond
represents the
Select key
Channel
Display
Solo Channel
Activates the joystick
– when off, channel is
not being controlled
underlying automation.
Strip Config 3
Joystick Assign Mode
Cycle
Direct Assign
402 Cycle
- Legal Notices 2
- Documentation Feedback 2
- Contents 3
- Chapter 1: Introduction 9
- System 5 hardware diagram 10
- System 5 Startup Sequence 11
- About This Guide 12
- About www.avid.com 12
- Connect and Play a CD 13
- Sources page in PatchNet 14
- Cabling-MADI Out Ports 15
- Chapter 3: eMix Application 17
- Projects Window 18
- Titles Window 19
- New Title dialog 20
- Mixes Window 21
- Select Current 22
- Edit Notes 22
- Title Defaults 23
- Normalled Connections 24
- Meter Presets 24
- PatchNet 25
- Console I/O 26
- Sources and Destinations 26
- Mic-Line Interface Patching 27
- Sources Window 28
- (see figure below) 29
- Nuendo and mics patched 30
- Mix Bus Send/Return 31
- Monitor Patching 31
- Solo Bus and Utility Patching 31
- Talkback Signal Patching 31
- PatchNet Presets 32
- Externals 33
- Mixer Model 34
- Changing Sample Rate 35
- DF66 Properties MADI tab 36
- Folddown 37
- Diagnostics 39
- System 5 Wave Logo 40
- Auto Failover 40
- Control Panel 40
- View Log 40
- Console Operation Logging 41
- Channel Strip 43
- CM401T Master Module 45
- Monitoring 46
- Monitor Source Selection 47
- Control Room Monitor Controls 48
- Cal Level 49
- Communications 50
- Talkback 51
- Listenback 52
- Oscillator/Slate 53
- Listen, and Slate/Osc 54
- Solo Mode 55
- Solo Level 55
- Solo Clear 55
- Solo Speaker Selection 56
- Solo Speaker Dim 56
- Solo-Safe 56
- Backstop PFL 56
- Meter Configuration 58
- Master Section Meters 59
- Channel Select Panel 63
- Knobset Panels 64
- Knobset Control Panel 65
- Bus Routing Panel 66
- Main Channel 68
- Swap Channel 68
- Meter and Status Display 68
- Channel Assign Panel 70
- Bus Assign Panel 71
- Input Names or Channel Number 72
- Strip Utilities 73
- Strip Expand 74
- Strip Zone Select 74
- Spill Select 74
- Fader Unity 74
- Fader Meters 75
- Knob and Fader Text Displays 75
- Joystick Assign Mode 75
- Delay Display Modes 76
- Aux View Enabled 76
- Knob Touch Enabled 76
- Channel Control Features 77
- All Mode 79
- Link Key 79
- Copy and Paste 79
- Talk (S5B Only) 79
- Channel Patch Points 81
- Channel Processor Order 82
- Insert Point 82
- Channel Functions 83
- Analog Controls 84
- Page keys display 84
- Input B and Signal Processing 84
- In/Out pages 84
- Digital Controls 84
- Stereo Controls 86
- Signal Processing In/Out 86
- Dynamics 87
- Expander/Gate (Page 2) 88
- Compressor (Page 3) 88
- Equalizers and Filters 89
- Parametric EQ 90
- Aux Sends 91
- Aux Send Config 92
- Rotate (Rot8) 93
- Focus Front (FocF) 93
- Pan Graph 94
- SmartPan 94
- Channel Mixing Functions 95
- Mix Bus Routing 96
- Mix Minus (S5B Only) 97
- Mix Busses 99
- Group Busses 99
- Auxiliary Sends 99
- Solo Busses 99
- Bus Master Functions 100
- Aux, Grp, and Mix Masters 101
- Bus Lock 101
- Mon Lock 101
- Group and Aux Busses 103
- Configuring Aux Busses 103
- Aux Copy 104
- AuxtoFader 104
- Pre/Post 104
- Fader Copy 104
- Mix and Group Bus Setup 105
- Bus Processing 105
- Snapshots, and Linking 107
- 12:24.03.10 109
- 00:16.12.04 109
- Transpor t Controls 110
- Locate Registers 110
- Feet + Frames Offset 111
- Film Type 111
- Locate Key 112
- Return Key 112
- Title Start 112
- Cue Points 113
- Track Arming 114
- Record in Motion 115
- On Transport Stop 115
- Auto Punch: Locate 115
- Machines - Setup Panel 116
- Control Groups 117
- Create Control Group 118
- Assign Control Group to Strip 118
- Modify Control Group 118
- Name Control Group 118
- Clear Control Group 118
- Multi Format Masters 119
- Spill Area 120
- New Layout 122
- Recall a Layout 123
- Modify a Layout 123
- Rename a Layout 123
- Delete a Layout 123
- Snapshots 124
- Recall a Snapshot 125
- Scene Automation 126
- Scenes Panel 127
- Creating a Link 129
- Modifying and Clearing a Link 129
- Link Suspend 130
- Links and Automation 130
- Joystick Linking 130
- Link Mode 131
- Automation Interface 134
- Automation LEDs 135
- Select/Punch Keys 135
- Automation Modes 136
- Write Trim 137
- Summary of Automation Modes 137
- Top of Strip 138
- Select/Punch key 138
- Strip Mode/Strip Function 139
- Recording Automation 140
- Switches 141
- Playing Back Automation 142
- Modifying Automation 143
- Knob Glide Modes 144
- Switch Automation 145
- Fill Features 146
- AutoFill 147
- Fill Start 148
- 00:12:24:03 149
- 00:16:11:04 149
- Fill Region + Fill End 150
- Fill Region + Fill Start 150
- Fill to Punch 150
- Auto Join 152
- Punch Capture 152
- Bus Master Automation 153
- Mix Assigns 153
- Automation Management 154
- Prune Tree 155
- Merge Trim 155
- Clear Automation 155
- Mix Offset 155
- Save Mix 155
- Automation Conform 156
- Hot Keys 157
- Operation Types 157
- Time Display 157
- Entering Notes 158
- Storing and Recalling Notes 158
- Reel Balancing 159
- Input Types 162
- Output Types 163
- Logical Operators 164
- Event Configuration Display 164
- Event List 165
- Deleting Events 166
- GPI Examples 166
- Audio Follow Video 170
- Camera Inputs 170
- 1 2 3 4 170
- CM403 Film/Post Module 173
- The Film Panel 174
- The PEC/DIR Panel 175
- < Page > Keys 176
- Sum and Solo Keys 176
- Ext Record Key 176
- Record, Preview Keys 176
- Wave Key 176
- Speaker Re-Assign 177
- Solo Control 178
- CM403 TFT Display 179
- Dual Joystick Panel 180
- Punching In a Joystick 181
- Multi-Operator Console 182
- Solo-In-Place 183
- Hybrid CM403 Joysticks 185
- Environmental Compliance 187
- Safety Compliance 188
- Technical Support (USA) 190
- Product Information 190
Produits connexes et manuels pour Logiciel Avid Technology System 5
(39 pages)
Logiciel Avid Technology System 5 Spécifications
(313 pages)
(313 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.106 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels